No — and this matters. The sound has to travel through the blocked speaker to do anything, so any connected Bluetooth or wired device defeats the purpose entirely. Disconnect everything first.
Tap the button below. It plays a low‑frequency sound that vibrates the speaker and pushes trapped water and dust out of the grille. Turn your volume up to about 80%.
💡 Point the speaker downward so gravity helps the water escape. Repeat 2–3 times if needed.
This tool is optimized for iPhone 15 devices. Select your exact model for the best results.
Dry the outside of your phone first.
Let gravity help pull the water out.
Ensure audio plays through the phone's internal speakers.
Never use earbuds. Turn volume up, but 100% isn't required.
Our tool is designed to target the three most common speaker issues using precise acoustic frequencies. Whether your phone took a dive or just sounds muffled from pocket lint, here is how we fix it.
Clear trapped water from your phone in about 60 seconds. The steady 165 Hz vibration physically pushes trapped liquid out of the speaker mesh.
A steady 165 Hz tone — the sweet spot for maximum diaphragm travel — physically pushes trapped water out.
Use our deep clean mode to act as a dust remover. Sweeping low frequencies shake loose stubborn dirt, sand, and lint.
Sweeps across low frequencies (120–400 Hz) to shake loose lint, dust and stubborn droplets the single tone misses.
Act as a volume booster for muffled speakers. Clear out blockages to restore heavy sound, loud bass, and crisp audio.
A clean 440 Hz reference tone so you can hear whether your speaker sounds clear again after cleaning.
Perfectly safe. These are ordinary frequencies your speaker already plays during music. The tool never exceeds normal listening levels — it just concentrates the energy at the frequency that moves water best.
The iPhone 15 was Apple's switch from Lightning to USB-C, and that change is genuinely relevant to liquid exposure — the two connectors behave differently when damp.
For a complete overview, see our full guide: Fixing an iPhone speaker.
Lightning exposes its contacts on the outside of the plug, where they sit directly against any moisture in the port. USB-C recesses its pins inside the connector shell. That difference does not make USB-C waterproof, but it does mean the contacts are less immediately exposed. The rule is unchanged: do not charge a wet port. Corrosion and short circuits remain entirely possible.
iOS displays a liquid-detection alert on USB-C models just as it did on Lightning. Do not use any override option — wait for the alert to stop appearing on its own. MagSafe and Qi wireless charging remain available and bypass the port completely.
The iPhone 15 line is rated IP68. As with every model, that is fresh water under laboratory conditions on a new device — seawater, chlorinated water, soap and steam all sit outside the test parameters.
Bottom-firing loudspeaker to the right of the USB-C port, earpiece above the display serving as the second stereo channel, microphone in the left-hand grille. The Dynamic Island did not change the earpiece slot's audio role — it still handles both calls and the upper stereo channel.
Inside the SIM tray slot on models that have one. Note that some iPhone 15 units in certain regions are eSIM-only with no physical tray, which removes that quick check — in those cases the indicator is not user-visible and only a technician can assess it.
Case off, exterior blotted dry, Bluetooth off entirely, volume 70–80 percent, grille facing straight down at roughly 45 degrees. Two or three cycles of 30–60 seconds, blotting between each.
iOS has no water-ejection feature on any iPhone including the 15. The function exists on Apple Watch only.
No — and this matters. The sound has to travel through the blocked speaker to do anything, so any connected Bluetooth or wired device defeats the purpose entirely. Disconnect everything first.
Eject the liquid the same way, but treat the device as needing professional attention afterwards. Salt and sugar leave conductive, corrosive residue when they dry, and that residue keeps damaging the board long after the speaker sounds normal.
Stop. If three cycles produce no improvement at all, the cause is not blockage. Check the symptoms on our guide to when a sound tool will not help, and have the device inspected rather than continuing to run cycles.
No. The frequencies used sit inside the range your speaker already reproduces whenever you play music, and the tool runs at moderate volume rather than maximum. The one genuine caution is earbuds: never run ejection tones into in-ear devices while you are wearing them.
No. Around 70 to 80 percent is the practical sweet spot. Maximum volume on a restricted diaphragm produces distortion rather than more displacement, and adds avoidable stress to the driver.
Our tool is great for water and dust, but it cannot fix physically blown speakers or electrical damage.
Learn when it won't workStep-by-step help for wet, muffled, crackling or quiet phone speakers.