Connect your Bluetooth device and play this sound to vibrate water and dust out of the headphone grilles.
💡 Point the speaker downward so gravity helps the water escape. Repeat 2–3 times if needed.
Water trapped in a speaker grille muffles the sound and can cause distortion. A strong, low‑frequency tone makes the speaker's diaphragm move a large distance back and forth — that mechanical vibration flicks droplets out of the mesh.
A steady 165 Hz tone — the sweet spot for maximum diaphragm travel — physically pushes trapped water out.
Sweeps across low frequencies (120–400 Hz) to shake loose lint, dust and stubborn droplets the single tone misses.
A clean 440 Hz reference tone so you can hear whether your speaker sounds clear again after cleaning.
Perfectly safe. These are ordinary frequencies your speaker already plays during music. The tool never exceeds normal listening levels — it just concentrates the energy at the frequency that moves water best.
Set your device to around 70–80% volume. The tool works by vibration, so it needs some power behind it.
Hold your phone with the speaker facing the floor or a soft cloth so water drains out instead of pooling deeper.
Press start and let the full cycle play. You may see or feel tiny droplets leave the grille.
Run it 2–3 times, then switch to “Test Sound” to confirm the audio is crisp again.
Wireless audio devices need noticeably different handling from phones, and one piece of advice matters more than all the others: never run ejection tones into earbuds while you are wearing them.
An earbud driver sits millimetres from your eardrum and is a fraction of the size of a phone speaker. Volume that is appropriate for a handset is not appropriate here. Remove them, place them mesh-down on a cloth, and use substantially lower volume — around half of what you would use on a phone is plenty.
Water gets the blame, but the common blockage in in-ear devices is cerumen packed into the speaker mesh. That does not respond to sound, because it is not loose debris — it is adhesive. It responds to careful dry cleaning: a soft dry brush, or adhesive putty pressed gently onto the mesh and lifted away. Never use liquid, and never use anything sharp on that mesh.
AirPods Pro and AirPods 3 onward carry IPX4 sweat and water resistance. That rating covers the buds themselves, not the charging case — and a soaked case is the more common failure. If the case got wet, leave it open, lid up, in moving air, and do not charge it until it is fully dry. Charging a damp case is how the contacts corrode.
Portable speakers use much larger drivers behind a fabric or rubber grille, and water tends to sit in the passive radiator cavity rather than on the driver. Because the driver is large, around 60–70 percent volume produces the same excursion that maximum would on a phone. If your speaker has a rubber port cover and that cover was open when it got wet, water is inside the electronics bay — leave it open to dry and do not connect power.
If you are trying to clear a phone speaker, any paired Bluetooth device defeats the exercise entirely, because the audio routes away from the speaker you are trying to clear. Turn Bluetooth off completely rather than just disconnecting.
Yes — for water trapped in the external speaker grille, the low‑frequency vibration is very effective. It cannot remove water from deep inside the device; if your phone was fully submerged, also power it off and let it air‑dry in a bag of rice or silica gel.
Completely. It plays standard audio frequencies at normal volume. It does not overdrive or damage the speaker. Just avoid setting the volume to 100% for long periods on cheap speakers, as with any loud audio.
Yes. It works on any device playing audio through this browser — phones, tablets, laptops and connected Bluetooth or wireless speakers.
Browsers only allow sound to start after you interact with the page. That single tap unlocks audio — after that the tool runs automatically.
No install and no account. Once the page has loaded it runs entirely on your device using your browser's built‑in audio engine.
The standard eject cycle takes about 15 to 60 seconds. We recommend running it 2-3 times for the best results.
Yes! It uses proven acoustic physics (specifically 165Hz tones) to physically push water and dust out of the speaker mesh.
This tool fixes muffled sound from water or dust. If your speaker is physically blown or crackling permanently, it will require hardware replacement at a repair shop.
Step-by-step help for wet, muffled, crackling or quiet phone speakers.