Stop. If three cycles produce no improvement at all, the cause is not blockage. Check the symptoms on our guide to when a sound tool will not help, and have the device inspected rather than continuing to run cycles.
Tap the button below. It plays a low‑frequency sound that vibrates the speaker and pushes trapped water and dust out of the grille. Turn your volume up to about 80%.
💡 Point the speaker downward so gravity helps the water escape. Repeat 2–3 times if needed.
This tool is optimized for On iPhone devices. Select your exact model for the most reliable result.
Dry the outside of your phone first.
Let gravity help pull the water out.
Ensure audio plays through the phone's internal speakers.
Never use earbuds. Turn volume up, but 100% isn't required.
Our tool is designed to target the three most common speaker issues using precise acoustic frequencies. Whether your phone took a dive or just sounds muffled from pocket lint, here is how we fix it.
Clear trapped water from your phone in about 60 seconds. The steady 165 Hz vibration physically pushes trapped liquid out of the speaker mesh.
A steady 165 Hz tone — the sweet spot for maximum diaphragm travel — physically pushes trapped water out.
Use our deep clean mode to act as a dust remover. Sweeping low frequencies shake loose stubborn dirt, sand, and lint.
Sweeps across low frequencies (120–400 Hz) to shake loose lint, dust and stubborn droplets the single tone misses.
Act as a volume booster for muffled speakers. Clear out blockages to restore heavy sound, loud bass, and crisp audio.
A clean 440 Hz reference tone so you can hear whether your speaker sounds clear again after cleaning.
Perfectly safe. These are ordinary frequencies your speaker already plays during music. The tool never exceeds normal listening levels — it just concentrates the energy at the frequency range where diaphragm travel is greatest.
A practical walkthrough rather than theory. Most iPhone-specific failures come from three setup mistakes, all of which take seconds to avoid.
For a complete overview, see what to check on an iPhone.
Start the tone playing, then press volume up. Pressing volume buttons before audio is playing adjusts the ringer instead of media. Aim for roughly 70–80 percent — not maximum, which clips the waveform and reduces the clean diaphragm travel that does the work.
Bottom grille facing straight down, phone tilted about 45 degrees so liquid runs off the casing rather than pooling beside the opening. Hold it away from your body — clothing absorbs expelled water and can wick it back.
Thirty to sixty seconds, then stop and blot the grille area dry before starting the next. Skipping the wipe means the next cycle's intake stroke draws the same water back in. Two or three cycles is the sensible limit for liquid.
If liquid is present, the tone often sounds slightly damped at first and then becomes noticeably cleaner and louder partway through, without you touching the volume. That change is the surface tension film breaking, and it is the best available confirmation that the mechanism engaged.
Record a Voice Memo before you start and play it back after each cycle at a fixed volume. Comparing against a fixed file is far more reliable than memory. Test the earpiece separately by making a call.
No port charging for 24 to 48 hours regardless of how good the speaker sounds. Use MagSafe or Qi.
Stop. If three cycles produce no improvement at all, the cause is not blockage. Check the symptoms on our guide to when a sound tool will not help, and have the device inspected rather than continuing to run cycles.
No. The frequencies used sit inside the range your speaker already reproduces whenever you play music, and the tool runs at moderate volume rather than maximum. The one genuine caution is earbuds: never run ejection tones into in-ear devices while you are wearing them.
No. Around 70 to 80 percent is the practical sweet spot. Maximum volume on a restricted diaphragm produces distortion rather than more displacement, and adds avoidable stress to the driver.
No — and this matters. The sound has to travel through the blocked speaker to do anything, so any connected Bluetooth or wired device defeats the purpose entirely. Disconnect everything first.
Eject the liquid the same way, but treat the device as needing professional attention afterwards. Salt and sugar leave conductive, corrosive residue when they dry, and that residue keeps damaging the board long after the speaker sounds normal.
Our tool is great for water and dust, but it cannot fix physically blown speakers or electrical damage.
Learn when it won't workStep-by-step help for wet, muffled, crackling or quiet phone speakers.