Eject the liquid the same way, but treat the device as needing professional attention afterwards. Salt and sugar leave conductive, corrosive residue when they dry, and that residue keeps damaging the board long after the speaker sounds normal.
Tap the button below. It plays a low‑frequency sound that vibrates the speaker and pushes trapped water and dust out of the grille. Turn your volume up to about 80%.
💡 Point the speaker downward so gravity helps the water escape. Repeat 2–3 times if needed.
This tool is optimized for For iPhone devices. Select your exact model for the most reliable result.
Dry the outside of your phone first.
Let gravity help pull the water out.
Ensure audio plays through the phone's internal speakers.
Never use earbuds. Turn volume up, but 100% isn't required.
Our tool is designed to target the three most common speaker issues using precise acoustic frequencies. Whether your phone took a dive or just sounds muffled from pocket lint, here is how we fix it.
Clear trapped water from your phone in about 60 seconds. The steady 165 Hz vibration physically pushes trapped liquid out of the speaker mesh.
A steady 165 Hz tone — the sweet spot for maximum diaphragm travel — physically pushes trapped water out.
Use our deep clean mode to act as a dust remover. Sweeping low frequencies shake loose stubborn dirt, sand, and lint.
Sweeps across low frequencies (120–400 Hz) to shake loose lint, dust and stubborn droplets the single tone misses.
Act as a volume booster for muffled speakers. Clear out blockages to restore heavy sound, loud bass, and crisp audio.
A clean 440 Hz reference tone so you can hear whether your speaker sounds clear again after cleaning.
Perfectly safe. These are ordinary frequencies your speaker already plays during music. The tool never exceeds normal listening levels — it just concentrates the energy at the frequency range where diaphragm travel is greatest.
iOS imposes constraints that shape what any cleaning tool can do on an iPhone, and a couple of them explain problems people mistake for the tool failing.
For a complete overview, see the iPhone troubleshooting walkthrough.
Safari supports the Web Audio API fully, so a web page can generate a tone locally with no installation, no permission prompt and nothing stored on the device. Given that iOS has no built-in water-eject function, this is the most direct route to the same mechanism Apple uses on the Watch.
iOS will not let a page produce audio without a deliberate tap. This is a deliberate anti-autoplay measure and it catches people out: a cycle that appears to be running silently is often waiting for the initial interaction. Tap the start control directly rather than expecting playback to begin on page load.
The ring/silent switch does not mute media playback on iOS, so that is rarely the cause. Media volume is separate from ringer volume though — start the tone playing first, then press volume up, which guarantees you are adjusting the right level.
Audio continues when the screen locks, but a browser tab may be suspended if you switch apps. Keep the tab in the foreground for the duration of a cycle.
Once the page has loaded, tone generation happens locally on the device — nothing is streamed. Load the page before you need it and leave the tab open if you expect to be without signal. Adding it to the home screen keeps it one tap away.
An installed app cannot produce a better result, because the limiting factor is the driver rather than the software. It can only add storage cost and permission prompts.
Eject the liquid the same way, but treat the device as needing professional attention afterwards. Salt and sugar leave conductive, corrosive residue when they dry, and that residue keeps damaging the board long after the speaker sounds normal.
Stop. If three cycles produce no improvement at all, the cause is not blockage. Check the symptoms on our guide to when a sound tool will not help, and have the device inspected rather than continuing to run cycles.
No. The frequencies used sit inside the range your speaker already reproduces whenever you play music, and the tool runs at moderate volume rather than maximum. The one genuine caution is earbuds: never run ejection tones into in-ear devices while you are wearing them.
No. Around 70 to 80 percent is the practical sweet spot. Maximum volume on a restricted diaphragm produces distortion rather than more displacement, and adds avoidable stress to the driver.
No — and this matters. The sound has to travel through the blocked speaker to do anything, so any connected Bluetooth or wired device defeats the purpose entirely. Disconnect everything first.
Our tool is great for water and dust, but it cannot fix physically blown speakers or electrical damage.
Learn when it won't workStep-by-step help for wet, muffled, crackling or quiet phone speakers.