Thirty to sixty seconds per cycle, repeated two or three times with short pauses. Running it continuously for many minutes adds nothing once the accessible liquid is out, and only heats the voice coil.
Tap the button below. It plays a low‑frequency sound that vibrates the speaker and pushes trapped water and dust out of the grille. Turn your volume up to about 80%.
💡 Point the speaker downward so gravity helps the water escape. Repeat 2–3 times if needed.
Select your issue and run the appropriate fix cycle to restore your speaker audio in about a minute.
Dry the outside of your phone first.
Let gravity help pull the water out.
Ensure audio plays through the phone's internal speakers.
Never use earbuds. Turn volume up, but 100% isn't required.
Our tool is designed to target the three most common speaker issues using precise acoustic frequencies. Whether your phone took a dive or just sounds muffled from pocket lint, here is how we fix it.
Clear trapped water from your phone in about 60 seconds. The steady 165 Hz vibration physically pushes trapped liquid out of the speaker mesh.
A steady 165 Hz tone — the sweet spot for maximum diaphragm travel — physically pushes trapped water out.
Use our deep clean mode to act as a dust remover. Sweeping low frequencies shake loose stubborn dirt, sand, and lint.
Sweeps across low frequencies (120–400 Hz) to shake loose lint, dust and stubborn droplets the single tone misses.
Act as a volume booster for muffled speakers. Clear out blockages to restore heavy sound, loud bass, and crisp audio.
A clean 440 Hz reference tone so you can hear whether your speaker sounds clear again after cleaning.
Perfectly safe. These are ordinary frequencies your speaker already plays during music. The tool never exceeds normal listening levels — it just concentrates the energy at the frequency range where diaphragm travel is greatest.
These two openings sit millimetres apart on most phones, face the same direction in your pocket, and collect the same debris from the same source. Fixing one without the other is a half job.
For a complete overview, see handling port and microphone debris.
Pocket lint. Both openings face upward in most pockets, and both are narrow enough to trap textile fibre. If your speaker is blocked, the port almost certainly has a compressed plug of lint in it too — whether or not charging has started failing yet.
The cable needs wiggling, or only connects at a certain angle, or the phone charges intermittently. The tell is that the cable feels like it does not go all the way in. This is almost always compacted lint rather than a worn connector — lint enters gradually and each insertion compresses it further, until the plug can no longer seat fully.
If liquid reached the speaker, it very likely reached the port too. This is where the charging rule comes from: voltage across damp connector pins corrodes them quickly, and it is the most common route from recoverable to permanent damage. Do not charge for 24 to 48 hours; use wireless charging if supported.
Same session, same tools, same source of debris. Clearing one and leaving the other means returning to the job in a few weeks.
Thirty to sixty seconds per cycle, repeated two or three times with short pauses. Running it continuously for many minutes adds nothing once the accessible liquid is out, and only heats the voice coil.
No. Around 70 to 80 percent is the practical sweet spot. Maximum volume on a restricted diaphragm produces distortion rather than more displacement, and adds avoidable stress to the driver.
No. Rice is a poor desiccant — open moving air dries a device faster — and its starch dust migrates into the charging port, microphone holes and speaker grille, which can create a second problem on top of the first.
Stop. If three cycles produce no improvement at all, the cause is not blockage. Check the symptoms on our guide to when a sound tool will not help, and have the device inspected rather than continuing to run cycles.
No. The frequencies used sit inside the range your speaker already reproduces whenever you play music, and the tool runs at moderate volume rather than maximum. The one genuine caution is earbuds: never run ejection tones into in-ear devices while you are wearing them.
Our tool is great for water and dust, but it cannot fix physically blown speakers or electrical damage.
Learn when it won't workStep-by-step help for wet, muffled, crackling or quiet phone speakers.