Thirty to sixty seconds per cycle, repeated two or three times with short pauses. Running it continuously for many minutes adds nothing once the accessible liquid is out, and only heats the voice coil.
Tap the button below. It plays a low‑frequency sound that vibrates the speaker and pushes trapped water and dust out of the grille. Turn your volume up to about 80%.
💡 Point the speaker downward so gravity helps the water escape. Repeat 2–3 times if needed.
Target a specific speaker on your device. Choose which speaker to clean, then run the fix.
Dry the outside of your phone first.
Let gravity help pull the water out.
Ensure audio plays through the phone's internal speakers.
Never use earbuds. Turn volume up, but 100% isn't required.
Our tool is designed to target the three most common speaker issues using precise acoustic frequencies. Whether your phone took a dive or just sounds muffled from pocket lint, here is how we fix it.
Clear trapped water from your phone in about 60 seconds. The steady 165 Hz vibration physically pushes trapped liquid out of the speaker mesh.
A steady 165 Hz tone — the sweet spot for maximum diaphragm travel — physically pushes trapped water out.
Use our deep clean mode to act as a dust remover. Sweeping low frequencies shake loose stubborn dirt, sand, and lint.
Sweeps across low frequencies (120–400 Hz) to shake loose lint, dust and stubborn droplets the single tone misses.
Act as a volume booster for muffled speakers. Clear out blockages to restore heavy sound, loud bass, and crisp audio.
A clean 440 Hz reference tone so you can hear whether your speaker sounds clear again after cleaning.
Perfectly safe. These are ordinary frequencies your speaker already plays during music. The tool never exceeds normal listening levels — it just concentrates the energy at the frequency range where diaphragm travel is greatest.
If one opening on your phone is going to clog, this is it. Its position and its grille shape both work against it, which is also why it responds best to acoustic cleaning.
For a complete overview, see clearing trapped water properly.
Three reasons compound. It faces upward in most pockets, so gravity feeds it. Its grille is typically a narrow slot, which draws liquid in by capillary action rather than repelling it. And it sits beside the charging port, so anything that reaches one opening tends to reach the other.
Unlike the earpiece, what accumulates here is pocket debris — textile fibre, skin cells, hair. Loose and mechanical rather than sticky and adhesive. That is good news, because loose material is exactly what acoustic cycles move well. The bottom speaker is the case where sound-based cleaning performs best.
They collect the same debris from the same source. A port that has become intermittent — the cable needs wiggling, or only works at an angle — is almost always packed with compressed lint rather than worn out. With the phone powered off, a wooden toothpick scraped gently along the back wall usually retrieves it as a single plug.
Many phones have symmetrical openings either side of the charging port, but only one contains a driver. The other is cosmetic. Cover each with a finger while audio plays — if the sound does not change, that side was never an output and cleaning it achieves nothing.
A case cut genuinely clear of the grille, rather than merely near it, is the single most effective change. Carrying the phone bottom-down in a pocket helps. And a monthly thirty-second brush prevents the slow accumulation people only notice once the sound has already degraded.
Thirty to sixty seconds per cycle, repeated two or three times with short pauses. Running it continuously for many minutes adds nothing once the accessible liquid is out, and only heats the voice coil.
Blockage produces quiet, never total silence. If there is no sound whatsoever, check that media volume is up, that no Bluetooth device is connected, and that Do Not Disturb is off. If all three are clear, the fault is hardware.
No — and this matters. The sound has to travel through the blocked speaker to do anything, so any connected Bluetooth or wired device defeats the purpose entirely. Disconnect everything first.
No. The frequencies used sit inside the range your speaker already reproduces whenever you play music, and the tool runs at moderate volume rather than maximum. The one genuine caution is earbuds: never run ejection tones into in-ear devices while you are wearing them.
Stop. If three cycles produce no improvement at all, the cause is not blockage. Check the symptoms on our guide to when a sound tool will not help, and have the device inspected rather than continuing to run cycles.
Our tool is great for water and dust, but it cannot fix physically blown speakers or electrical damage.
Learn when it won't workStep-by-step help for wet, muffled, crackling or quiet phone speakers.