Stop. If three cycles produce no improvement at all, the cause is not blockage. Check the symptoms on our guide to when a sound tool will not help, and have the device inspected rather than continuing to run cycles.
Tap the button below. It plays a low‑frequency sound that vibrates the speaker and pushes trapped water and dust out of the grille. Turn your volume up to about 80%.
💡 Point the speaker downward so gravity helps the water escape. Repeat 2–3 times if needed.
Select your issue and run the appropriate fix cycle to restore your speaker audio in about a minute.
Dry the outside of your phone first.
Let gravity help pull the water out.
Ensure audio plays through the phone's internal speakers.
Never use earbuds. Turn volume up, but 100% isn't required.
Our tool is designed to target the three most common speaker issues using precise acoustic frequencies. Whether your phone took a dive or just sounds muffled from pocket lint, here is how we fix it.
Clear trapped water from your phone in about 60 seconds. The steady 165 Hz vibration physically pushes trapped liquid out of the speaker mesh.
A steady 165 Hz tone — the sweet spot for maximum diaphragm travel — physically pushes trapped water out.
Use our deep clean mode to act as a dust remover. Sweeping low frequencies shake loose stubborn dirt, sand, and lint.
Sweeps across low frequencies (120–400 Hz) to shake loose lint, dust and stubborn droplets the single tone misses.
Act as a volume booster for muffled speakers. Clear out blockages to restore heavy sound, loud bass, and crisp audio.
A clean 440 Hz reference tone so you can hear whether your speaker sounds clear again after cleaning.
Perfectly safe. These are ordinary frequencies your speaker already plays during music. The tool never exceeds normal listening levels — it just concentrates the energy at the frequency that moves water best.
Some blockages come out in a single cycle and some resist everything. The difference is not severity — it is what the material is bonded by.
For a complete overview, see our full guide: Diagnosing what is actually wrong.
Water held by surface tension, and dry particulate resting in the mesh. Both are held mechanically, and mechanical force removes them. This is what acoustic cleaning is for, and within that scope it works well.
Oil, earwax, dried sugar, and fibre that got damp and set as it dried. These are attached by adhesion rather than resting. Vibration applies mechanical force, and mechanical force does not break an adhesive bond — so increasing volume only heats the voice coil while the residue stays exactly where it was.
No amount of persistence changes this. It is a category difference, not a severity difference.
Material that has entered the acoustic cavity sits behind the diaphragm's airflow and behind any brush. Nothing at home reaches it. This is why compressed air fired into a grille is so damaging — it converts a recoverable blockage into this category permanently.
Run three cycles properly — case off, grille brushed, Bluetooth off, 70–80 percent, facing down. If there is no audible change at all, the material is bonded or beyond the mesh. Partial improvement that then stops means some was loose and some was not.
Adhesive putty, pressed lightly and lifted straight off, five or six times with a fresh face each time. This is the only home method that lifts bonded surface residue rather than redistributing it.
If putty and brushing do not help, the residue has penetrated. A repair shop can remove the assembly and clean it with solvent or an ultrasonic bath — usually inexpensive relative to a screen or battery repair.
Stop. If three cycles produce no improvement at all, the cause is not blockage. Check the symptoms on our guide to when a sound tool will not help, and have the device inspected rather than continuing to run cycles.
No. The frequencies used sit inside the range your speaker already reproduces whenever you play music, and the tool runs at moderate volume rather than maximum. The one genuine caution is earbuds: never run ejection tones into in-ear devices while you are wearing them.
Thirty to sixty seconds per cycle, repeated two or three times with short pauses. Running it continuously for many minutes adds nothing once the accessible liquid is out, and only heats the voice coil.
No. Around 70 to 80 percent is the practical sweet spot. Maximum volume on a restricted diaphragm produces distortion rather than more displacement, and adds avoidable stress to the driver.
No. Rice is a poor desiccant — open moving air dries a device faster — and its starch dust migrates into the charging port, microphone holes and speaker grille, which can create a second problem on top of the first.
Our tool is great for water and dust, but it cannot fix physically blown speakers or electrical damage.
Learn when it won't workStep-by-step help for wet, muffled, crackling or quiet phone speakers.