No. Around 70 to 80 percent is the practical sweet spot. Maximum volume on a restricted diaphragm produces distortion rather than more displacement, and adds avoidable stress to the driver.
Tap the button below. It plays a low‑frequency sound that vibrates the speaker and pushes trapped water and dust out of the grille. Turn your volume up to about 80%.
💡 Point the speaker downward so gravity helps the water escape. Repeat 2–3 times if needed.
Set exactly how long you want the speaker cleaning to run. We recommend 1-2 minutes for best results.
Dry the outside of your phone first.
Let gravity help pull the water out.
Ensure audio plays through the phone's internal speakers.
Never use earbuds. Turn volume up, but 100% isn't required.
Our tool is designed to target the three most common speaker issues using precise acoustic frequencies. Whether your phone took a dive or just sounds muffled from pocket lint, here is how we fix it.
Clear trapped water from your phone in about 60 seconds. The steady 165 Hz vibration physically pushes trapped liquid out of the speaker mesh.
A steady 165 Hz tone — the sweet spot for maximum diaphragm travel — physically pushes trapped water out.
Use our deep clean mode to act as a dust remover. Sweeping low frequencies shake loose stubborn dirt, sand, and lint.
Sweeps across low frequencies (120–400 Hz) to shake loose lint, dust and stubborn droplets the single tone misses.
Act as a volume booster for muffled speakers. Clear out blockages to restore heavy sound, loud bass, and crisp audio.
A clean 440 Hz reference tone so you can hear whether your speaker sounds clear again after cleaning.
Perfectly safe. These are ordinary frequencies your speaker already plays during music. The tool never exceeds normal listening levels — it just concentrates the energy at the frequency that moves water best.
Different parts of this take very different amounts of time, and conflating them is why people either give up too early or wait unnecessarily.
For a complete overview, see our full guide: Diagnosing what is actually wrong.
Case off, exterior blotted dry, Bluetooth turned off in settings, volume set while audio is playing, grille brushed. Rushing this stage is the commonest cause of poor results.
Two or three cycles of 30–60 seconds, with a wipe between each. Most of the actual work happens in the first twenty seconds of the first cycle — that is when the surface tension film breaks.
Four or five passes of 30–45 seconds with brushing between each. Dust improves gradually rather than suddenly, because each pass frees a little more.
Playing back a reference voice memo, testing each driver separately, and running a manufacturer diagnostic if your device has one.
Completely separate from the speaker and far longer. Even with the speaker sounding perfect, moisture remains around the charging port and inside the chassis. Upright, moving air, no heat, no rice.
Not charging for 24 to 48 hours. A clear speaker tells you the cavity is clear — it tells you nothing about the charging port. Voltage across damp pins is the most common route from recoverable to permanent damage, and it is entirely avoidable by waiting.
Running the tone continuously for eight or ten minutes. Once the accessible water is out, additional runtime only heats the voice coil, which raises resistance and reduces output as it continues.
No. Around 70 to 80 percent is the practical sweet spot. Maximum volume on a restricted diaphragm produces distortion rather than more displacement, and adds avoidable stress to the driver.
Stop. If three cycles produce no improvement at all, the cause is not blockage. Check the symptoms on our guide to when a sound tool will not help, and have the device inspected rather than continuing to run cycles.
No. The frequencies used sit inside the range your speaker already reproduces whenever you play music, and the tool runs at moderate volume rather than maximum. The one genuine caution is earbuds: never run ejection tones into in-ear devices while you are wearing them.
Thirty to sixty seconds per cycle, repeated two or three times with short pauses. Running it continuously for many minutes adds nothing once the accessible liquid is out, and only heats the voice coil.
For maintenance, roughly once a month is plenty. More often if you exercise heavily, work outdoors, or live somewhere humid or dusty. There is no benefit to daily use on a speaker that sounds fine.
Our tool is great for water and dust, but it cannot fix physically blown speakers or electrical damage.
Learn when it won't workStep-by-step help for wet, muffled, crackling or quiet phone speakers.