No. Around 70 to 80 percent is the practical sweet spot. Maximum volume on a restricted diaphragm produces distortion rather than more displacement, and adds avoidable stress to the driver.
Tap the button below. It plays a low‑frequency sound that vibrates the speaker and pushes trapped water and dust out of the grille. Turn your volume up to about 80%.
💡 Point the speaker downward so gravity helps the water escape. Repeat 2–3 times if needed.
Select your issue and run the appropriate fix cycle to restore your speaker audio in about a minute.
Dry the outside of your phone first.
Let gravity help pull the water out.
Ensure audio plays through the phone's internal speakers.
Never use earbuds. Turn volume up, but 100% isn't required.
Our tool is designed to target the three most common speaker issues using precise acoustic frequencies. Whether your phone took a dive or just sounds muffled from pocket lint, here is how we fix it.
Clear trapped water from your phone in about 60 seconds. The steady 165 Hz vibration physically pushes trapped liquid out of the speaker mesh.
A steady 165 Hz tone — the sweet spot for maximum diaphragm travel — physically pushes trapped water out.
Use our deep clean mode to act as a dust remover. Sweeping low frequencies shake loose stubborn dirt, sand, and lint.
Sweeps across low frequencies (120–400 Hz) to shake loose lint, dust and stubborn droplets the single tone misses.
Act as a volume booster for muffled speakers. Clear out blockages to restore heavy sound, loud bass, and crisp audio.
A clean 440 Hz reference tone so you can hear whether your speaker sounds clear again after cleaning.
Perfectly safe. These are ordinary frequencies your speaker already plays during music. The tool never exceeds normal listening levels — it just concentrates the energy at the frequency that moves water best.
If cleaning has not worked and the symptoms point at hardware, the next step is a technician. Choosing well matters more for liquid damage than for most repairs.
For a complete overview, see our full guide: Repair, replace, or live with it.
Speaker replacement is routine work almost anywhere. Liquid damage is not — it needs board-level inspection and ultrasonic cleaning, which many general repair shops do not do. If your device has been wet, ask specifically whether they perform ultrasonic board cleaning and corrosion inspection. A shop that only swaps modules will replace the speaker, and if the board is corroding the new speaker will fail too.
A firm price quoted before anyone has opened the device. Reluctance to give a written estimate. No warranty on the work. Pressure to authorise immediately. And for liquid damage specifically, a shop that does not ask what kind of liquid it was — because salt water and sugary drinks change the job substantially.
Manufacturer service is more expensive and preserves warranty and water resistance more reliably. Independent shops are cheaper and often faster, but may use aftermarket parts and will usually void remaining warranty. For a device still under warranty, go to the manufacturer first — though be aware liquid damage is typically excluded from standard cover regardless.
When a quoted repair approaches half the device's current resale value, replacement usually makes more sense — particularly on an older phone that will need a battery soon anyway.
No. Around 70 to 80 percent is the practical sweet spot. Maximum volume on a restricted diaphragm produces distortion rather than more displacement, and adds avoidable stress to the driver.
No. Rice is a poor desiccant — open moving air dries a device faster — and its starch dust migrates into the charging port, microphone holes and speaker grille, which can create a second problem on top of the first.
Stop. If three cycles produce no improvement at all, the cause is not blockage. Check the symptoms on our guide to when a sound tool will not help, and have the device inspected rather than continuing to run cycles.
No. The frequencies used sit inside the range your speaker already reproduces whenever you play music, and the tool runs at moderate volume rather than maximum. The one genuine caution is earbuds: never run ejection tones into in-ear devices while you are wearing them.
Thirty to sixty seconds per cycle, repeated two or three times with short pauses. Running it continuously for many minutes adds nothing once the accessible liquid is out, and only heats the voice coil.
Our tool is great for water and dust, but it cannot fix physically blown speakers or electrical damage.
Learn when it won't workStep-by-step help for wet, muffled, crackling or quiet phone speakers.