Tap the button below. It plays a low‑frequency sound that vibrates the speaker and pushes trapped water and dust out of the grille. Turn your volume up to about 80%.
💡 Point the speaker downward so gravity helps the water escape. Repeat 2–3 times if needed.
Select your issue and run the appropriate fix cycle to restore your speaker audio in about a minute.
Dry the outside of your phone first.
Let gravity help pull the water out.
Ensure audio plays through the phone's internal speakers.
Never use earbuds. Turn volume up, but 100% isn't required.
Our tool is designed to target the three most common speaker issues using precise acoustic frequencies. Whether your phone took a dive or just sounds muffled from pocket lint, here is how we fix it.
Clear trapped water from your phone in about 60 seconds. The steady 165 Hz vibration physically pushes trapped liquid out of the speaker mesh.
A steady 165 Hz tone — the sweet spot for maximum diaphragm travel — physically pushes trapped water out.
Use our deep clean mode to act as a dust remover. Sweeping low frequencies shake loose stubborn dirt, sand, and lint.
Sweeps across low frequencies (120–400 Hz) to shake loose lint, dust and stubborn droplets the single tone misses.
Act as a volume booster for muffled speakers. Clear out blockages to restore heavy sound, loud bass, and crisp audio.
A clean 440 Hz reference tone so you can hear whether your speaker sounds clear again after cleaning.
Perfectly safe. These are ordinary frequencies your speaker already plays during music. The tool never exceeds normal listening levels — it just concentrates the energy at the frequency range where diaphragm travel is greatest.
The name promises more than any sound-based tool can deliver, so it is worth being precise about the scope.
For a complete overview, see how to clear liquid from a speaker.
It plays a low-frequency tone through your device's own speaker. That tone moves the diaphragm through its full travel, and each stroke pumps air against whatever is sitting in the speaker cavity — pushing trapped liquid and loose debris out through the grille. Gravity carries it away, which is why orientation matters.
It removes obstructions. It repairs nothing. A speaker that is muffled because of water or lint will sound normal again once cleared — that feels like a fix and is a genuine restoration of lost performance. A speaker with a torn diaphragm, a corroded contact or a broken cable is unaffected, because there is nothing to remove.
Blockage sounds muffled but complete — quieter and duller, but nothing missing and nothing rattling. Damage sounds different: buzzing that worsens as volume rises means a torn diaphragm; total silence means a broken connection, because obstruction produces quiet and never silence.
Nothing, and there is no reason it should. Generating a tone is a few lines of code that every browser already supports — no server work, no licensing, no processing cost.
Case off. Blot the exterior dry. Bluetooth off entirely. Volume 70–80 percent, not maximum. Grille facing straight down at about 45 degrees. 30–60 second cycles with a wipe between each.
Do not charge a wet device for 24 to 48 hours, however good the speaker sounds. A clear speaker tells you the cavity is clear — not that the charging port is dry.
See also: what the tool can and cannot fix.
No. The frequencies used sit inside the range your speaker already reproduces whenever you play music, and the tool runs at moderate volume rather than maximum. The one genuine caution is earbuds: never run ejection tones into in-ear devices while you are wearing them.
Thirty to sixty seconds per cycle, repeated two or three times with short pauses. Running it continuously for many minutes adds nothing once the accessible liquid is out, and only heats the voice coil.
No. Around 70 to 80 percent is the practical sweet spot. Maximum volume on a restricted diaphragm produces distortion rather than more displacement, and adds avoidable stress to the driver.
No. Rice is a poor desiccant — open moving air dries a device faster — and its starch dust migrates into the charging port, microphone holes and speaker grille, which can create a second problem on top of the first.
Stop. If three cycles produce no improvement at all, the cause is not blockage. Check the symptoms on our guide to when a sound tool will not help, and have the device inspected rather than continuing to run cycles.
Our tool is great for water and dust, but it cannot fix physically blown speakers or electrical damage.
Learn when it won't workStep-by-step help for wet, muffled, crackling or quiet phone speakers.