Tap the button below. It plays a low‑frequency sound that vibrates the speaker and pushes trapped water and dust out of the grille. Turn your volume up to about 80%.
💡 Point the speaker downward so gravity helps the water escape. Repeat 2–3 times if needed.
Select your issue and run the appropriate fix cycle to restore your speaker audio in about a minute.
Dry the outside of your phone first.
Let gravity help pull the water out.
Ensure audio plays through the phone's internal speakers.
Never use earbuds. Turn volume up, but 100% isn't required.
Our tool is designed to target the three most common speaker issues using precise acoustic frequencies. Whether your phone took a dive or just sounds muffled from pocket lint, here is how we fix it.
Clear trapped water from your phone in about 60 seconds. The steady 165 Hz vibration physically pushes trapped liquid out of the speaker mesh.
A steady 165 Hz tone — the sweet spot for maximum diaphragm travel — physically pushes trapped water out.
Use our deep clean mode to act as a dust remover. Sweeping low frequencies shake loose stubborn dirt, sand, and lint.
Sweeps across low frequencies (120–400 Hz) to shake loose lint, dust and stubborn droplets the single tone misses.
Act as a volume booster for muffled speakers. Clear out blockages to restore heavy sound, loud bass, and crisp audio.
A clean 440 Hz reference tone so you can hear whether your speaker sounds clear again after cleaning.
Perfectly safe. These are ordinary frequencies your speaker already plays during music. The tool never exceeds normal listening levels — it just concentrates the energy at the frequency range where diaphragm travel is greatest.
Simple, numbered instructions in plain English. Each step has a reason attached, because knowing why a step matters makes it much easier to get right.
For a complete overview, see the water removal method in full.
Phone covers very often sit over part of the speaker slot. Water pushed out then gets trapped against the opening and goes back in. Take it off before starting.
Use a soft dry cloth and press gently rather than rubbing. Rubbing pushes water into the small gaps around the screen and ports. If water is still on the outside, the sound cycle will pull some of it inward.
This is the mistake that wastes the most time. If earphones or a car system are connected, the phone sends the sound there instead of to the wet speaker, and nothing happens. Turn Bluetooth off in settings, not just disconnect.
About 70 to 80 percent. Not full volume. At maximum the sound becomes distorted and the speaker membrane stops moving smoothly, which actually reduces the pushing action.
Start the sound playing first, then press the volume button — otherwise you may be changing ringtone volume instead of media volume.
Speaker facing straight down, phone tilted about 45 degrees. This is not a small detail. Held flat, the water comes out and settles right back. Facing down, gravity carries it away.
30 to 60 seconds each time. Stop, wipe the speaker area dry, then run again. Two or three times is enough for water.
24 to 48 hours. Do not plug in the charger even if the speaker sounds perfect. A clear speaker only tells you the speaker is clear, not that the inside of the phone is dry.
No rice — open moving air dries faster and rice powder enters the ports. No hair dryer — heat damages the thin membrane. Nothing sharp in the speaker grille — the mesh inside tears easily.
No. The frequencies used sit inside the range your speaker already reproduces whenever you play music, and the tool runs at moderate volume rather than maximum. The one genuine caution is earbuds: never run ejection tones into in-ear devices while you are wearing them.
Thirty to sixty seconds per cycle, repeated two or three times with short pauses. Running it continuously for many minutes adds nothing once the accessible liquid is out, and only heats the voice coil.
No. Around 70 to 80 percent is the practical sweet spot. Maximum volume on a restricted diaphragm produces distortion rather than more displacement, and adds avoidable stress to the driver.
No. Rice is a poor desiccant — open moving air dries a device faster — and its starch dust migrates into the charging port, microphone holes and speaker grille, which can create a second problem on top of the first.
Stop. If three cycles produce no improvement at all, the cause is not blockage. Check the symptoms on our guide to when a sound tool will not help, and have the device inspected rather than continuing to run cycles.
Our tool is great for water and dust, but it cannot fix physically blown speakers or electrical damage.
Learn when it won't workStep-by-step help for wet, muffled, crackling or quiet phone speakers.